Precautions for Lightweight and Interesting Use

Lightweight concrete foaming agent is also called foam concrete foaming agent. It refers to the additive that can reduce the surface tension of the liquid and produce a large amount of uniform and stable foam. It is an admixture used in the production of foamed concrete, which can provide a considerable amount of foam. substance. How is cement foaming agent used in actual production? Tongrun's professional foam concrete admixture supplier will show you how to use high-quality lightweight concrete and precautions in the actual production of cement foaming agents.

How to use lightweight concrete foaming agent

1. Because the concentration of cement foaming agent is generally significant, direct use of foaming opportunities will result in low foam output and waste foaming agent. Directly added to the foaming computer will generally have a relatively high concentration and cannot produce high-quality foam. At the same time, it is easy to block the inlet pump of cement foaming machine. The dilution ratio and foaming effect of cement foaming agent are huge. Therefore, if the dilution factor is too high or too low, there must be a very suitable dilution factor. When determining the reasonable dilution ratio of cement foaming agent, one should refer to the dilution ratio recommended by the manufacturer on the one hand, and on the other hand,

2. After determining the multiple, it needs to be diluted with water to form a foaming liquid, and then the foaming liquid is transformed into a foam product. Pour water and foaming agent into the water tank to fully dissolve it. After observing the blisters, pour the prepared cement into the container, then fully stir it with a stirring tool, and then transport it through a high-pressure conveying pipe or manually. Processed into finished products in wallboard machinery.

Precautions for the use of lightweight concrete foaming agent

1. Note that when the dilution ratio with water is too low, the concentration of the foaming agent diluent is too high, the overall foam volume will be reduced, and the amount of foaming agent will increase. When the dilution factor is less than 30 times, the foam output decreases and the added slurry collapses. When we dilute it to 50 times, the overall foam output will increase. If the added mud does not collapse significantly, the foam output will increase by 30%. Therefore, when the lightweight concrete foaming agent is diluted to 50 times, both the foam yield and quality are higher than the dilution by 30 times or less.

2. When the dilution ratio is too high, more foam will be formed, less liquid will be formed, the foam conversion rate of the foaming agent diluent will be low, the foam output will decrease, and the foam stability will decrease. Therefore, only when the dilution ratio is appropriate, a foam with high foam output and high durability can be obtained.

3. Note that when purchasing the main material foaming agent, it does not mean that the dilution ratio is high, so the dosage is small. What kind of blowing agent should be distinguished? For example, synthetic blowing agents are usually diluted hundreds of times, but this is not the case. It is less than 40 times diluted than animal foaming agent.

Synthetic blowing agent overview

Synthetic foaming agent for concrete is a highly concentrated,highly efficient liquid,which is used in the production of lightweight foam concrete,Foam concrete is also known as cellular lightweight concrete (CLC).

CLC concrete has very good potential to help construct honeycomb lightweight applications.Using the correct type of foaming agent can make a huge difference in product properties (such as the mechanical properties of concrete and its resistance,etc.).Synthetic foaming agents are chemical substances that reduce the surface tension of liquids,and are commonly used in the manufacture of blocks, bricks,CLC concrete,etc.worldwide.Compared with other foaming agents,when high density is required,less energy is required for formation.It is strongly recommended for use in the construction sector where the demand for lightweight concrete is increasing over time.

Synthetic foaming agent for concrete advantages

1.Low cost / high concentration

Synthetic foaming agent for concrete has a low usage rate and it is this which must be considered when choosing a foaming agent,not just its basic price per litre.

2.Fine foam and good stability

It can be used in a wide range of temperature and water quality.This stability means that the foam bubbles sustain themselves and support the mortar around them.The bubbles do not burst easily and hence the foamed concrete does not collapse when it is made or after it has been placed.

3.The amount of bleeding is low.

4.Excellent strength and thermal insulation properties.

It means that the foamed concrete produced from Tongrun Foaming Agent is ideal for a wide range of applications.

5.Foaming Agent is essentially harmless and easily washes off.

Instructions of synthetic foaming agent for concrete 

Water and foaming agent are fed separately into the Foam Generator which mixes them in the correct ratio (see diagram below).The mixture of water and foaming agent is called the pre-foaming solution.Pre-foaming solution and compressed air are fed through a lance;

Foaming Agent can be used with all types of cement and incorporated into cement only,or sand-cement mortar slurries to produce foamed concrete of every type and for every application.Its cost as a proportion of the total cost of foamed concrete is tiny,typically only about 1-3%.

Synthetic blowing agent application

1.Foaming Agent  is used for making lightweight(clc) blocks and panels;

2.Foaming agent is used for void filling;

Foam Concrete is also very useful for void filling.As it is very fluid it will pour into even the most inaccessible places.It can be used for planned work,but also in emergencies to provide stability and support very quickly;

3.Foaming agent is used for Roofing Insulation;

4.Foaming agent is used for marking CLC blocks,Cast-in-place wall,bridge strengthening wall construction, floor construction, lightweight precast blocks,fire breaks,sound Insulation,etc.

Synthetic blowing agent price

The price of synthetic blowing agents will vary randomly with the production cost, transportation cost, international situation, exchange rate, and market supply and demand of synthetic blowing agents. Tanki New Materials Co., Ltd. aims to help all industries and chemical wholesalers find high-quality, low-cost nanomaterials and chemicals by providing a full set of customized services. If you are looking for a synthetic blowing agent, please feel free to send an email to get the latest synthetic blowing agent prices.

Synthetic blowing agent suppliers

As a global synthetic blowing agent supplier,Tanki New Materials Co.,Ltd has extensive experience in the performance,application and cost-effective manufacturing of advanced and engineered materials.The company has successfully developed a series of powder materials (including water-based stearic acid emulsion,water-based calcium stearate,zinc stearate,etc.),high-purity targets,functional ceramics and structural devices,and provides OEM services.